Printer Resetter Service Manual

1. Double click AdjProg.exe.
2. Click “Accept” button.
3. Click "Select" button. and select your printer model then click "OK"
4. Click “Particular adjustment mode” button.
5. Select on “Waste ink pad counter” and click “OK” button.
6. Click on “Initialization” button and the program will reset the protection counter.
7. Turn off the printer as a program instructed then turn on again.
8. Click “Finish” button. and its done!

Warning: You might end up with ink leaking out of the printer if you dont either replace the waste ink pad or install external waste bin.

• Switch on the printer.
• Set computer date setting (if the adjustment programs require date setting).
• Run the adjustment program.
• Set printer model then click ok (if exist, usually there are adjustment program can be used at more than one printer).
• Click Maintenance Tab
• Check Protection counter.
• Click protection counter to reset counter to zero.
• Then click Ok, Ok
• switch off printer for 5secs then switch on again
• done

1. Switch on printer.
2. Set computer date setting (if the adjustment programs require date setting).
3. Run the adjustment program.
4. Set printer model then click ok (if exist, usually there are adjustment program can be used at more than one printer).
5. Click particular adjustment mode.
6. Select waste ink pad counter in the maintenance section then click ok or double click the menu.
7. Click on “check button” or “read button” till its done then click on “initialization button” then click “finish”.
8. switch off printer for 5secs then switch on again
9. done

• Turn on the Printer.
• Set date setting in your computer to 4 October 2007.
• Run Adjustment Program by clicking “AdjProg.exe”.
• Select Accept
• Select Particular adjustment mode
• Select “Waste ink pad counter – OK
• Click Initialization to reset current protection counter to “Zero”.
• Turn off printer and turn on again.

• Download and extract the file.
• Run “ServiceFT.exe”
• Select waste ink pad counter from maintenance item, double click to execute it.
• Click Initialization button to reset current protection counter to Zero.
• Read(again) after “0″ press finish
• Choose set shipping data (bottom menu)
• Choose set
• Wait for a while (about 1 minute)
• If there is a reaction from the printer (it will load some paper or you hear “klothak” sound), the reset process will be done. turn off the printer and then turn on again. repeat read the EEPRsaya
• If there is no reaction from the printer, repeat step 1

• Run the software (Adjustment TX100 and TX105 no instalation require). Then click accept button. Click select button to seledt your printers type. Available two coiche.  Epson TX100 or Epson TX105, Ok. Click paticular adjustment mode.
  
• Click waste ink pad counter from maintenance menu, OK.
  
• Click check to view status counter of your printers. Click initialization to reset the counter.
  

1. Start with printer on, press aadditional functions, Scan, Copy, Scan. Now you should be in service mode.
2. Select Test mode which is like the last available selection
3. Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

• The menu will now say EEPRsaya Clear
• Select Ink count which is option (0) and press set
• Then press Reset Followed by the power button and then wait for it to restart.

1. Turn off printer and open printer.
2. Open your Epson main PCB board. You can view an 8 pin CMOS IC. That is Epson waste ink counter IC and found on all Epson Printer.
3. You can reset your printer without any resetter by following these ways.
4. Soldering pin no 1,2,3,4 by wire as show in PICTURE and now turn on printer for ”20 second”
5. After 20 second turn off printer and remove soldering wire from pin no. 1,2,3,4 ( back in original condition)
6. Now turn on your printer
7. And now your printer will be RESET
   
   Note : This method is not recommended for beginners so you have to understand what you are doing. All problem caused by this tutorials is not our responsibility. Use this tutorial as your own risk.

• Download link adjustment epson tx100 –> http://www.mediafire.com/file/2dzmkwkjjoa/TX100.zip
• Download link Adjustment epson t10 –> http://www.mediafire.com/file/neuqgzzmxln/T10.zip

• Download Adjustment Program Epson T10
• Download Adjustment Program Epson TX100