Wednesday, March 6, 2013
fix or repair HP 7310 Printer
You will need a T10 Torx (star) screwdriver, available from Home Depot, Sears and the like.
1. Remove rear door
2. Remove 2 screws from the back panel
3. Lift rear panel and wiggle - May break on one side
4. Unplug 3 x flat cables and 1 x molex. Unscrew flat cable clamp
5. Pull out left side cover so that scanner can be lifted vertical and removed
6. Remove the encoder strip releasing at the non-spring end (right side when viewed from the front)
7. Take your time with this, it is easy to rip the hole
8. Release carriage belt from motor and pulley
9. Remove 3 screws from the carriage shaft/bar and slide the bar out. DO NOT turn the printer upside down after doing this.
The carriage should now be free but still attached by the 2 flat cables
10. Unplug the 2 flat cables
Read more...
1. Remove rear door
2. Remove 2 screws from the back panel
3. Lift rear panel and wiggle - May break on one side
4. Unplug 3 x flat cables and 1 x molex. Unscrew flat cable clamp
5. Pull out left side cover so that scanner can be lifted vertical and removed
6. Remove the encoder strip releasing at the non-spring end (right side when viewed from the front)
7. Take your time with this, it is easy to rip the hole
8. Release carriage belt from motor and pulley
9. Remove 3 screws from the carriage shaft/bar and slide the bar out. DO NOT turn the printer upside down after doing this.
The carriage should now be free but still attached by the 2 flat cables
10. Unplug the 2 flat cables
Epson R230 printer repair and printer Close To Open
Epson R230 printer cover is not as easy as opening other types of printers such as Epson C79, C90 C58, C45, T11, T20 and the Epson Stylus C45. On this occasion, if we want to fix the printer a lot of steps should we consider when disassembling the printer, because so many key baud and installed by the manufacturer, perhaps because of the size of the printer that is larger than previous versions and to strengthen the body of the printer own. Here are the steps to open the Epson R230 printer:
First prepared with tools such as:
1. Plus size screwdriver (+)
2. Small-sized screwdriver min (-)
3. Baud storage (so that not all baud when unpacking splattered everywhere)
After setting up tools on top of us straight to the point of dismantling the Epson R230:
1. Open the back of the printer baud 3 baud here there has to be opened, note the picture below
2. Open the printer cover left and right side by prying the retaining cap bottom first, and proceed to the back side, and so on the inside. note the picture below:
3. in the second part is not done in a hurry, do it with a heart-to-day and look carefully the parts of a binding cap printer, this process applies exactly the same
4. as opening the lid next to it.
5. At this stage we can do many things, such as:
Read more...
First prepared with tools such as:
1. Plus size screwdriver (+)
2. Small-sized screwdriver min (-)
3. Baud storage (so that not all baud when unpacking splattered everywhere)
After setting up tools on top of us straight to the point of dismantling the Epson R230:
1. Open the back of the printer baud 3 baud here there has to be opened, note the picture below
2. Open the printer cover left and right side by prying the retaining cap bottom first, and proceed to the back side, and so on the inside. note the picture below:
3. in the second part is not done in a hurry, do it with a heart-to-day and look carefully the parts of a binding cap printer, this process applies exactly the same
4. as opening the lid next to it.
5. At this stage we can do many things, such as:
- clean the inside of the printer
- replace rubber puller roll paper
- etc.
Subscribe to:
Posts (Atom)