Tuesday, September 17, 2013
Browse »
home»
hp
»
How to Clean Scanner Mirrors on HP3330
This is not an Hewlett Packard document, the author does not work for
Hewlett Packard and is not responsible for any damage you do to your
printer. This procedure is for skilled repair technicians and is not
recommended without some knowledge of equipment repair. Proceed at your
own risk.
1. Open the document feeder and pull up on the two black tabs on the left and right.
2. Pull up on the right part of the doc feeder then the left, remove doc feeder, set aside.
3. Open front door and rear fuser door.
4. Remove screws closest to teal colored fuser release levers. (side cover screws)
5. Pull right cover out from back while releasing clip on bottom of cover, pull cover towards the back and remove.
6. Push on indentation at back of left cover and pull out at back, this cover is hinged.
7. Remove four screws now visible at base of scanner assy., two on left two on right.
8. Slide covers towards back and remove.
9.
Remove two screws in the back just above the fuser and just below the
scanner assy. base. Remove two screws in the front, visible now after
removing the scanner assy. base covers on the right and left (the left
one is just behind the hinged cover near the top hinge.)
10. Remove flat ribbon cable (on left side) at either connection point to disconnect scanner assy. from print engine.
11. Entire scanner assembly can now be slid forward and removed.
12. Close the front, rear and left side doors on the print engine portion and set it aside.
13. Grab front panel face plate at top and pull forward and remove. (or pry gently at top of face plate).
14.
At top of exposed front panel you will see four slots in the scanner
assy. At the third one from the left there is a latch (dark grey
plastic). Push down on the latch with a screwdriver and slide the whole
panel assy. to the right. Lift up and out making sure to disconnect the
cable.
15. Remove the three screws in the now exposed dark grey front
panel cradle and cover, remove the two cables connecting the cover to
the main board, pry gently at the top outer corners of the cover and
pull it forward and down, remove the cover.
16. Now remove the four
scanner assy. screws (one and the center front, center back, center
right, center left) all are facing down under the assy. (Or just flip it
upside down and remove the four visible screws.
17. Turn the unit
back upright and remove the four screws at the back/top (two of them are
down inside where the doc feeder normally goes.) Remove the top scanner
cover.
18. DANGER your about to work on the scanner carriage itself
there is a really good chance that you could break it or the mirrors or
bulb so proceed at your own risk.
19. At the top and bottom left side
of the black cover enclosing the mirrors are two slots, if you put a
small screwdriver in the slots and push gently to the right and lift
that side of the cover it should come loose. Then open it to the right
and remove it from the right slots.
20. Remove the black screw at the
front of the assy., Disconnect the white wires from the CCD board and
out of the harness, lift the clear plastic bulb holder out with the bulb
then remove it from the rear. (it’s a tight fit at the front.)
21.
The top mirror is held in by some really tight clips they have to be
removed from the bottom right (clean the mirrors without this step if
possible). NOTE: optical mirrors are not like a bathroom mirror, there
is no glass covering the reflective surface. The back side of the mirror
has glass covering it so if you get it in backwards it won’t work. (The
way to tell which side you have is touch your screwdriver to the mirror
and if it’s the right side the screwdriver will appear to touch the
reflection of the screwdriver, if it’s the wrong side the screwdriver
will not touch the reflection of the screwdriver because of the glass
covering the reflective surface.
22. Now clean the remaining mirrors
and lens very thoroughly with alcohol. Make sure they are very clean.
You can put the top mirror back and clean it in place to make cleaning
it easier.
23. When re-assembling the top cover check to make sure the white strip on the right side is clean.
24. Reverse procedure for re-assembly.
How to Clean Scanner Mirrors on HP3330
Hewlett Packard and is not responsible for any damage you do to your
printer. This procedure is for skilled repair technicians and is not
recommended without some knowledge of equipment repair. Proceed at your
own risk.
1. Open the document feeder and pull up on the two black tabs on the left and right.
2. Pull up on the right part of the doc feeder then the left, remove doc feeder, set aside.
3. Open front door and rear fuser door.
4. Remove screws closest to teal colored fuser release levers. (side cover screws)
5. Pull right cover out from back while releasing clip on bottom of cover, pull cover towards the back and remove.
6. Push on indentation at back of left cover and pull out at back, this cover is hinged.
7. Remove four screws now visible at base of scanner assy., two on left two on right.
8. Slide covers towards back and remove.
9.
Remove two screws in the back just above the fuser and just below the
scanner assy. base. Remove two screws in the front, visible now after
removing the scanner assy. base covers on the right and left (the left
one is just behind the hinged cover near the top hinge.)
10. Remove flat ribbon cable (on left side) at either connection point to disconnect scanner assy. from print engine.
11. Entire scanner assembly can now be slid forward and removed.
12. Close the front, rear and left side doors on the print engine portion and set it aside.
13. Grab front panel face plate at top and pull forward and remove. (or pry gently at top of face plate).
14.
At top of exposed front panel you will see four slots in the scanner
assy. At the third one from the left there is a latch (dark grey
plastic). Push down on the latch with a screwdriver and slide the whole
panel assy. to the right. Lift up and out making sure to disconnect the
cable.
15. Remove the three screws in the now exposed dark grey front
panel cradle and cover, remove the two cables connecting the cover to
the main board, pry gently at the top outer corners of the cover and
pull it forward and down, remove the cover.
16. Now remove the four
scanner assy. screws (one and the center front, center back, center
right, center left) all are facing down under the assy. (Or just flip it
upside down and remove the four visible screws.
17. Turn the unit
back upright and remove the four screws at the back/top (two of them are
down inside where the doc feeder normally goes.) Remove the top scanner
cover.
18. DANGER your about to work on the scanner carriage itself
there is a really good chance that you could break it or the mirrors or
bulb so proceed at your own risk.
19. At the top and bottom left side
of the black cover enclosing the mirrors are two slots, if you put a
small screwdriver in the slots and push gently to the right and lift
that side of the cover it should come loose. Then open it to the right
and remove it from the right slots.
20. Remove the black screw at the
front of the assy., Disconnect the white wires from the CCD board and
out of the harness, lift the clear plastic bulb holder out with the bulb
then remove it from the rear. (it’s a tight fit at the front.)
21.
The top mirror is held in by some really tight clips they have to be
removed from the bottom right (clean the mirrors without this step if
possible). NOTE: optical mirrors are not like a bathroom mirror, there
is no glass covering the reflective surface. The back side of the mirror
has glass covering it so if you get it in backwards it won’t work. (The
way to tell which side you have is touch your screwdriver to the mirror
and if it’s the right side the screwdriver will appear to touch the
reflection of the screwdriver, if it’s the wrong side the screwdriver
will not touch the reflection of the screwdriver because of the glass
covering the reflective surface.
22. Now clean the remaining mirrors
and lens very thoroughly with alcohol. Make sure they are very clean.
You can put the top mirror back and clean it in place to make cleaning
it easier.
23. When re-assembling the top cover check to make sure the white strip on the right side is clean.
24. Reverse procedure for re-assembly.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment